ETP_S_Bare_Cathedral_Port_Cylinder_Head_for_LS2_and_LS6_6_0L_243_Casting_01_la

ETP’S Bare Cathedral Port Cylinder Head for LS2 and LS6 6.0L 243 Casting

ETP'S Bare Cathedral Port Cylinder Head for LS2 and LS6 6.0L 243 Casting
ETP'S Bare Cathedral Port Cylinder Head for LS2 and LS6 6.0L 243 Casting
ETP'S Bare Cathedral Port Cylinder Head for LS2 and LS6 6.0L 243 Casting
ETP'S Bare Cathedral Port Cylinder Head for LS2 and LS6 6.0L 243 Casting

ETP'S Bare Cathedral Port Cylinder Head for LS2 and LS6 6.0L 243 Casting
The home of New & Used Engine Parts. Parts Stored Inside and Out of Weather. ETP’S Bare Cathedral Port Cylinder Head for LS2 and LS6 6.0L 243 Casting. Intake Valve Head Diameter. Exhaust Valve Head Diameter. There is NO requirement for you to send us your old head or parts. A little about us. We setup our Shanghai operations in 2004 for the purpose of controlling the quality of our parts as they are being manufactured. This quality gateway has been very successful and a huge benefit to our customers by allowing us to offer great quality parts at very competitive prices. It is recommended to have your parts assembled and fitted by a qualified person. If you dont know what youre doing get someone who does. ETP use the following carriers to deliver our orders. Please note that some orders using Australia Post will not have tracking numbers. How to Return an Item. A return address will be provided once you have contacted ETP. All second hand parts are stamped with a ETP punch. Ensure you are returning the correct part. It is important you inspect the part correctly before fitment, and ensure it is correct for your application. Any failure of your engine due to use of Second Hand Parts is solely your responsibility. Please Read This Before Installing Parts. Used or Second Hand parts are NOT. ETP Engine Parts Pty Ltd have supplied the product/s from our interpretation of the information the you the customer provided. However, it is the customers responsibility to compare the supplied components to the original part/s they are replacing to ensure compatibility and the required quality is correct. We are here to help! The words’our’,’we’ and’the company’ in this document refer to ETP Engine Parts Pty Ltd. All our goods are supplied with guarantees which cannot be excluded under the Australian Consumer Law. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Please note that the above clause only applies where you make a valid claim pursuant to the Australian Consumer Law. Without limiting the effect of the Australian Consumer Laws, ETP Engine Parts Pty Ltd may take into consideration the following non-exhaustive list of factors in assessing the validity of any claim made under the Australia Consumer Law, particularly where. [i] There is in fact any fault of defect. [ii] You change your mind. [iii] ETP Engine Parts Pty Ltd bought to your attention any hidden defect before purchasing the part. [iv] You examined the part before purchasing and/or fitment and should have noticed the fault. [v] You used the goods in a manner which caused the goods to become unacceptable, damaged or to fail. [vi] You took reasonable steps to avoid the quality becoming unacceptable, damaged or to fail. [viii] Something occurred which was beyond human control and that occurred after the part was supplied. In the event that the ETP Engine Parts Pty Ltd finds that any of the above have occurred, ETP Engine Parts Pty Ltd may investigate, oppose or defend that claim under Australia Consumer Laws. Correct Product Fitment and Installation Procedures. [ii] If no fitting requirements have been provided, you must use your best endeavours to ensure that the parts are fitted with reasonable due care and diligence by a suitably qualified person and in accordance with the OE Manufactures instructions. [ii] Any product which has been damaged due to the fault of any other product component. [iii] Any product which has not been fitted in accordance with the listed Fitting Requirements. [iv] Damage to the product from a failure of the owner to properly repair the product or any other product component which effects the product. [v] Damage to the product due to airborne contamination (or’dusting’) entering the air intake system. [vi] Damage to the product caused by operations a contradiction to the instrumentation/gauge warning devices high water temperature and low oil pressure, etc. And includes a’dry-start’ condition. [vii] Damage to the part associated to the incorrect timing or caused by faulty ancillary components. [viii] A part which is incorporated in a product which hand been fitted with an aftermarket turbocharger or supercharging system, or has been modified in any way to obtain additional horsepower/torque. However, ETP Engine Parts Pty Ltd are not the carrier and therefore, will not be held responsible for any damage or loss incurred in the transportation process. ETP Engine Parts Pty Ltd cannot guarantee that their decision will be in your favour. [x] Products installed into marine and industrial engines which have not been run-in on a dynamometer. [xiv] Unauthorised repairs, alterations or dismantling of any description. [xv] Wear and tear from normal operation. [xvi] Second hand/used parts. All claims will require detailed invoices/receipts proving that all our conditions were met at the time of the product installation. Parts: ETP Engine Parts Pty Ltd will supply free of charge all components required to rectify any authorised claims and also reserves the right to supply used components in certain circumstances. Reimbursement of cost to Purchaser: If the part has been inspected by ETP Engine Parts Pty Ltd and has been deemed warrantable by us, ETP Engine Parts Pty Ltd may in its absolute discretion reimburse reasonable charges for outside preliminary inspections, the product’s removal and it’s return cost. Customer’s responsibilities and entitlements. A cease operation of the product immediately. A form will be posted/emailed to you and reference number provided. The Purchaser must accept one of the repair measures proposed by ETP Engine Parts Pty Ltd within a reasonable time. [vii] If the purchaser proposes an alternative repair measure which is not endorsed by ETP Engine Parts Pty Ltd, we may at our absolute discretion undertake repair work in accordance with the purchaser’s proposed repair measures. The third party Engineer must be from the MVRIA or the Office of Fair Trading or be a recognised Automotive Consultant with membership of the SAE and IAME. [xi] Any Opinion expressed or determination made by the third party expert shall not bind ETP Engine Parts Pty Ltd or the purchaser. Get the latest news, updates and special offers about our store. The item “ETP’S Bare Cathedral Port Cylinder Head for LS2 and LS6 6.0L 243 Casting” is in sale since Monday, January 20, 2020. This item is in the category “Vehicle Parts & Accessories\Car & Truck Parts\Engines, Components\Cylinder Heads & Parts”. The seller is “etp_online” and is located in Campbellfield VIC. This item can be shipped worldwide.
  • Brand: ETP
  • Manufacturer Part Number: CHLSN-243
  • MPN: CHLSN243

ETP'S Bare Cathedral Port Cylinder Head for LS2 and LS6 6.0L 243 Casting